Miscellaneous

Device Authorization Profile

This feature will define a set of commands that can be executed/denied execution by a specific user/user group on Infraon NCCM. Administrators can also restrict/permit command execution authorization based on device models.

Click "Device Authorization Profile" and "OK" to proceed.

• Input the Template Name

  • Template Name must be unique.

• Select the Template Group using the dropdown menu.

• Select Vendor using the dropdown menu.

  • This is mandatory since Template commands are specific to vendor devices.

• Select the OS Type

  • This is mandatory since Template commands are specific to vendor device OS types. If commands are executable on all vendor devices, input them as ALL TYPE.

• Input the Model details.

• Input the Series details.

• Approval Required Checkbox is mandatory, and the user cannot uncheck it.

(This is a compliance requirement).

• Input the Template Description.

Click the "Template Configurations" panel.

Infraon NCCM accepts command input only in the regex pattern. Command inputs are split into five sections. They are:

• Terminate Commands - Command (sets) denied for execution by the User/User Group. When a user tries these set(s) of commands, Infraon NCCM terminates the CLI Session immediately.

• Block Commands - Command (sets) denied for execution by the User/User Group. When a user tries these set(s) of commands, Infraon NCCM blocks these commands from being executed. The CLI session is not terminated here.

• Notify Commands - When a user tries these set(s) of commands, Infraon NCCM executes the same and triggers a notification about the action. Notifier (Notification Alert) must be selected using the dropdown menu if this option is selected.

• Permit Commands – Command (sets) permitted for execution by the User/User Group. Commands not added in the ‘Permit’ section will be blocked during execution.

• System Commands – used to ignore inputs like password and other User credential input. For example, when a user tries to execute a command that requires authentication by the system, the system prompts the user to provide additional information. In this case, a system prompt must be added in the ‘Ignore’ section. If not, the system runs the command through the Permit command list and may block the command/command set.

There are two ways to input commands:

1. Adding commands in the respective text boxes.

2. Importing saved commands from a file. To import commands, click on the respective button:

Load Terminate Commands from File, Load Block Commands from File, Load Notify Commands from File, Load Permit Commands from File, Load System Commands from File

Click the "Access Control" panel

• Select the visibility

Note: If the visibility is “Private,” the User and User group dropdown will be enabled, and the selected user and administrator will only be able to manage this template.

• Select the User(s).

• Select the User group(s).

• Click "Save" to save the template with the given input.

Action Icons

Multiple action icons are displayed on the top right corner of the page.

Actions Icons | Fields

Label	Actions
Filter	Click to use filter options to search
Add	Click to add 'Configure Template'
Edit	Click to edit a Template
Delete	Click to delete a Template
Production Ready	Click to mark the template ready for Production
Enable	Click to enable template
Disable	Click to disable Template
Execute	Click to execute the template immediately
Import	Click to import Template
Export	Click to export Template

Configuration Template Filter

NCCM allows the filtering of Configuration Templates based on the following columns.

• Template Name

• Vendor

• OS Type

• Model

• Template type

• Active Status

• Template Group

• Production Status

• Approval State

Click "Search" to perform the filter-based search based on the selection of filter columns.

Note: NCCM supports full match and pattern match for user input fields.

Edit Template

Select an existing template and click on "Edit" to edit. Edit operation follows the same steps as ‘Add Template’. Other than Template Type, all other fields on the template can be modified.

Delete Template

Select the Template(s), and to delete the Template, click on the delete icon.

Click "YES" to delete the Template or "NO" to cancel the delete operation.

Enable Template

Select Template(s) and click to enable the template, i.e., to move the template state to active. Only Active Templates will be used in the Upload job and Network Diagnosis.

Disable Template

Select Template(s) and click to disable the template. Disabled templates will not be used in the Upload job and Network Diagnosis.

Production Ready

Select Template(s) and click to change the templates’ Production status to active. Only Active production Templates will be used in the Upload job and Network Diagnosis. Templates manually created by the user will be saved in Production Ready and Enabled State. In the case of Import Templates, the Production Ready status will be in the ‘Disabled’ state.

Note: Templates imported into NCCM using Excel must be changed manually to the ‘Production Ready’ state.

Execute/Add Upload Job

Click to execute the template, redirecting to ‘Add an Upload Job’.

Template Import

Click to upload/Import the template file (Only .xls file format is supported).

Template Export

Click to export NCCM’s configured Templates to the XLS file. Click to download/export the templates to an Excel file.